How to Assemble a Goodevas Swedish Wall Safely: Step-by-Step

Quick answer

Mount your Goodevas Swedish wall into solid wood studs or a masonry wall using the supplied hardware, keep the bottom rail at least 10–15 cm above the floor, and test every anchor with firm hand pressure before a child climbs. If you cannot find studs or suitable masonry, stop and use a proper mounting board or consult a professional.

A Swedish wall turns a small wall space into a daily climbing and training corner, but the installation decides whether it stays safe after the first enthusiastic swing. Goodevas wall bars are designed for home assembly, yet the wall itself is the part most people underestimate.

This guide walks through the full process: checking the wall, planning height, assembling the frame, anchoring it, and running a final safety test. It also covers how add-ons like the Jungle Play Set change what you need to check before installation.

Before you start: tools, wall type, and space check

Clear the area and gather a spirit level, tape measure, pencil, drill, stud finder, and a ladder. Check that the wall is solid — plasterboard alone will not hold a climbing wall safely. You need either wood studs, concrete, brick, or a properly fixed mounting board. If you are unsure, ask a qualified installer to confirm.

Measure the free wall height and width. Goodevas Swedish wall products are designed for indoor use, and the lower rail should sit at least 10–15 cm above the floor so feet have room. Leave at least 60 cm of clear space in front for safe landing and movement.

• Do not mount into drywall alone, even with heavy-duty plugs.
• Check for hidden cables and pipes before drilling.

Step 1: Find and mark the studs or anchoring points

Use a stud finder to locate the vertical studs behind the wall. Mark their centers with a pencil. The wall bars need to be fixed into at least two studs, ideally more, so the load spreads across the frame. For masonry, mark drill points at the same spacing as the wall bar rails.

Hold the assembled or partially assembled frame against the wall and mark the top and bottom fixing holes with a spirit level. Do not trust the floor line — it is often uneven. The wall bars must be level for safe climbing and for add-ons to fit correctly.

• Common mistake: drilling before checking for pipes or wires behind the plaster.
• Checkpoint: every fixing point should align with a stud or a solid masonry anchor.

Step 2: Assemble the wall bar frame on the floor

Lay the side rails and rungs on a soft surface to avoid scratches. Follow the Goodevas instructions for your specific model — rung spacing and hardware can differ between sets. Tighten bolts by hand first, then fully tighten once the frame is square.

Check the frame for square by measuring the diagonals. If they match, the frame is true. If not, loosen and adjust before final tightening. A square frame sits flat against the wall and prevents stress on individual rungs.

• Do not fully tighten bolts until the frame is square.
• Keep small parts and tools away from children during assembly.

Step 3: Lift and fix the frame to the wall

With a helper, lift the frame into position and insert the top fixings first. Check level again, then insert the lower fixings. Tighten each anchor gradually in a cross pattern so the frame does not pull to one side.

For masonry, use the correct drill bit size and blow dust out of the holes before inserting anchors. For studs, use structural screws long enough to reach the stud center. Never substitute shorter or thinner hardware than supplied.

• Common mistake: over-tightening one anchor and stripping it.
• Checkpoint: the frame should not move when you push it sideways with moderate force.

Step 4: Install add-ons and check clearances

If you are adding a Jungle Play Set or other accessory, install it after the main wall is secure. Add-ons increase the load and change the swing area, so re-check that there is enough clear space around the wall. The 7in1 Jungle Play Set, for example, unfolds into a larger sports corner with a pull-up bar and slides, so it needs more room than a bare wall.

Follow the accessory instructions for attachment points. Do not hang add-ons from rungs that are not designed for that load. If a product description does not state a weight limit, treat that as a decision limitation and keep use within the intended age and activity.

• Check that slides and swings do not hit furniture, doors, or radiators.
• Keep the landing area clear and use a soft mat if the floor is hard.

Step 5: Final safety test and daily checks

Push and pull the frame firmly in several directions, then hang briefly from the top bar if it is designed for that. Check every bolt and anchor for movement. If anything shifts, stop and re-fix it before a child uses the wall.

Make checking part of your routine: tighten bolts monthly, look for wall cracks around anchors, and inspect ropes, swings, and slides for wear. A Swedish wall is a training tool, not a babysitter — supervise younger children, especially during the first sessions.

• Re-tighten all fixings after the first week of use.
• Stop use immediately if the wall moves or makes cracking sounds.

Assembly steps at a glance

1. Check the wall and clear the area: Confirm studs or masonry, remove obstacles, and leave at least 60 cm of clear space in front. If the wall is plasterboard only, stop and use a mounting board or professional help.
2. Mark and drill fixing points: Use a spirit level and stud finder; mark top and bottom holes so the frame sits level. Never drill without checking for hidden cables and pipes.
3. Assemble the frame square: Lay parts on the floor, tighten by hand, check diagonals, then fully tighten. An out-of-square frame will not sit flat and can stress the rungs.
4. Fix the frame to the wall: Insert top fixings first, re-check level, then add lower fixings and tighten gradually. The frame should not move when pushed sideways.
5. Add accessories and test: Install add-ons after the main wall is secure, then push, pull, and hang-test every fixing. Re-tighten all bolts after the first week and check monthly.

Goodevas products that affect your setup

• 7in1 Jungle Play Set for Kids: Swedish Ladder+ Monkey Bars + Swing Set + Slide Board + Ramp: Folded, it functions as a standard Swedish wall with a rope set; unfolded, it becomes a complete sports corner with a pull-up bar and two slides. Ideal for children from 2 years old. Because it unfolds into a larger play area, plan extra clear space and check that the wall can take the added dynamic load before installing.
• Jungle Play Set for Swedish Walls: This add-on set expands the functionality of the Swedish wall with movable monkey bars, a large slide, and a transition element. It is an accessory, so install it only after the main wall is secure, and verify that your existing wall model supports the attachment points.
• Gym Addition to the Climbing Ladders: This accessory transforms your triangle ladder into a multi-functional Swedish ladder equipped with a horizontal bar for pull-ups and hangs. If you add a horizontal bar, check that the ladder is stable and that the wall fixings are rated for pulling forces, not just static climbing.

A safe Goodevas Swedish wall setup comes down to solid anchoring, a level frame, and regular checks. Take the time to find studs, use the right hardware, and test the wall before your child climbs. If anything feels uncertain, bring in a professional — it is a small cost for lasting peace of mind.